Setting Up a Raspberry Pi for Linux Real-Time Experiments
A Raspberry Pi is an extremely useful platform for exploring Linux internals: inexpesive, widely tested and documented, it runs a conventional Linux kernel, provides direct access to hardware interfaces, and can be controlled via remote access.
This article gives step-by-step instruction how prepare a Raspberry Pi 4 running the 64-bit Raspberry Pi OS Lite distribution with remote access.
The objective is to create a reproducible starting point for later experiments involving GPIO, kernel scheduling, timing and real-time behaviour.
Tested configuration: Raspberry Pi 4 Model B Rev 1.5 (1 GB RAM), Raspberry Pi OS Lite 64-bit, Linux kernel 6.18.50+rpt-rpi-v8. Price: AUD $90
1. Hardware and software
- Raspberry Pi 4 Model B, revision 1.5, with 1 GB RAM
- 64 GB microSD card
- Raspberry Pi power supply
- Debian Linux workstation
- Local network connection
We will use Raspberry Pi OS Lite (64-bit), without a graphical desktop.
The Raspberry Pi will operate headlessly: no monitor, keyboard or mouse.
2. Prepare the microSD card
Insert the microSD card into the Linux workstation using a suitable USB reader.
Identify the device:
lsblk -o NAME,SIZE,MODEL
In my case, the relevant device appeared as:
sde 58.2G MassStorageClass
└─sde1 58.2G
The reported capacity of 58.2 GiB is consistent with a nominal 64 GB card.
Note: Device names are not fixed. The card may appear as /dev/sdb, /dev/sdc or something else. Identify the correct device carefully before writing an image.
There is no need to format the card beforehand; raspberry Pi Imager writes the operating-system image, including its partition table and filesystems.
3. Install Raspberry Pi OS
From Linux workstation, download the Raspberry Pi Imager AppImage:
wget https://downloads.raspberrypi.com/imager/imager_latest_amd64.AppImage
chmod +x imager_latest_amd64.AppImage
./imager_latest_amd64.AppImage
Run Raspberry Pi Imager and select:
- Device: Raspberry Pi 4
- Operating system: Raspberry Pi OS Lite (64-bit)
- Storage: 64 GB microSD card
- Hostname:
pi4 - Username:
pi - SSH: Enabled
- Raspberry Pi Connect: Disabled
Network credentials were configured during imaging, allowing the Pi to join the network automatically on its first boot.
After the image was written and verified, insert the card into the Raspberry Pi and connected the power supply.
4. Establish SSH access
Once the Pi has booted and joined the network, from the Linux workstation:
ssh pi@pi4.local
The .local hostname uses multicast DNS (mDNS), avoiding the need to discover or
configure a fixed IP address.
During the first boot, the intended hostname did not resolve immediately. This required inspecting the network advertisements using Avahi:
avahi-browse -art | grep -i pi
The Pi initially appeared as pi4-2.local. After a subsequent reboot, the expected
hostname pi4.local became available.
This illustrates a useful practical point: network discovery and hostname resolution may require investigation even when the underlying SSH service is working correctly.
5. Configure and update the system
The initial SSH session reported that the workstation’s Australian locale was unavailable on the Pi. Inspect the installed locales:
locale
locale -a
Configure the required locale:
sudo dpkg-reconfigure locales
In this case, I enabled en_AU.UTF-8 and selected it as the default.
Next, update Raspberry Pi OS:
sudo apt update
sudo apt full-upgrade
sudo reboot
After rebooting, reconnected using SSH.
6. Inspect the Linux system
Identify the running kernel:
uname -a
Raspberry Pi reported:
Linux pi4 6.18.50+rpt-rpi-v8 #1 SMP PREEMPT
The system runs a 64-bit ARM Linux kernel.
Next, inspect the processor:
lscpu
The relevant characteristics:
| Property | Observed value |
|---|---|
| Architecture | aarch64 |
| Processor | ARM Cortex-A72 |
| CPU cores | 4 |
| Maximum CPU frequency | 1800 MHz |
| Minimum CPU frequency | 600 MHz |
Inspect memory:
free -h
The Pi reported approximately 905 MiB of usable RAM, consistent with its nominal 1 GB configuration.
Identify the board:
cat /sys/firmware/devicetree/base/model
Result:
Raspberry Pi 4 Model B Rev 1.5
Finally, inspect the SoC temperature:
cat /sys/class/thermal/thermal_zone0/temp
The measurement was:
41868
The value is expressed in millidegrees Celsius, corresponding to approximately 41.9 °C.
7. Summary
This tutorial built:
- A 64-bit ARM Linux system
- Remote SSH access
- A conventional Linux kernel
- Command-line access to system and hardware information
- GPIO interfaces available for subsequent experiments
The system has no GUI and is operated entirely from a remote Linux workstation.
A particularly interesting detail is the kernel’s PREEMPT designation. Does that mean
the Raspberry Pi is running a real-time Linux kernel?
Not necessarily.
In the next article, we inspect the kernel configuration and distinguish ordinary kernel
preemption from the PREEMPT_RT real-time kernel.